Dante383 at 18:36, 10 September 2024

2024-09-10T18:36:20Z

← Older revision		Revision as of 18:36, 10 September 2024
Line 8:		Line 8:
	==== Ignition switch connector ====		==== Ignition switch connector ====
	'''Female (harness) side connector: KUM PH772-06015'''		'''Female (harness) side connector: KUM PH772-06015'''

	'''Female (harness) side terminals: Faston 6.3mm'''		'''Female (harness) side terminals: Faston 6.3mm'''
	{\| class="wikitable"		{\| class="wikitable"

Dante383 at 18:36, 10 September 2024

2024-09-10T18:36:00Z

← Older revision		Revision as of 18:36, 10 September 2024
Line 1:		Line 1:
	{{Draft}}		{{Draft}}This article won't cover the most basic ECU<>K-Line adapter connection since all information required for that can be found in the ECU pinout pages.

			Instead, we will focus on creating a more complete environment that'll reassemble the actual car - allowing you to swap parts, test inter-connected systems such as the [[immobiliser]], and most importantly - research. The purpose of this article is mostly to organize connector part numbers and pinouts in one place so the process is more straightforward for the next person
			[[File:Ignition switch connectors.jpg\|thumb]]

			=== Ignition switch - key sensor, immobiliser antenna, illumination ===

			==== Ignition switch connector ====
			'''Female (harness) side connector: KUM PH772-06015'''
			'''Female (harness) side terminals: Faston 6.3mm'''
			{\| class="wikitable"
			\|+
			! colspan="3" \|Ignition switch pinout. Female side, looking from the front
			<tab>
			\|-
			\|#3. Ignition output
			\|#2. +12v input
			\|#1. Starter output
			\|-
			\|#6. Ignition output
			\|#5. +12v input
			\|#4. Accessory output
			\|}
			As seen in the diagram below, #3 and #6 power different BCM fuses but they're essentially the same and swapping them won't do any harm[[File:Ignition switch.png\|thumb\|#1 - key sensor, #2 - immobiliser antenna coupled with ignition illumination, #3 - ignition switch ]]
			[[File:Ignition switch diagram.png\|left\|thumb]]

			==== Key sensor, immobiliser antenna, key illumination ====
			'''Female (harness) side connector: KET MG651044 / Yazaki 7283-1060'''

			'''Female (harness) side terminals: ???'''
			{\| class="wikitable"
			\|+
			! colspan="4" \|Key sensor pinout. Female side, looking from the front
			<tab>
			\|-
			\|#2. Immobiliser antenna
			(BCM-HM 1)
			\|
			\|
			\|#1. Immobiliser antena
			(BCM-HM 11)
			\|-
			\|#6. Ground
			\|#5. Key sensor
			(BCM-HM 4)
			\|#4. Key sensor
			(BCM-JM 3)
			\|#3. +12v illumination input
			(BCM-KM 10)
			\|}

Dante383 at 16:27, 10 September 2024

2024-09-10T16:27:11Z

← Older revision		Revision as of 16:27, 10 September 2024
Line 1:		Line 1:
	{{Draft}		{{Draft}}

Dante383: Created page with "{{Draft}"

2024-09-10T16:26:36Z

Created page with "{{Draft}"

New page

{{Draft}

Creating a test bench setup - Revision history

Dante383 at 18:36, 10 September 2024

Dante383 at 18:36, 10 September 2024

Dante383 at 16:27, 10 September 2024

Dante383: Created page with "{{Draft}"